MB19 Series/
MB17 Series
LCD Monitor
User Guide
MENU
Table of contents
Notices................................................................................................. iv
Safety.information................................................................................ v
Care.&.Cleaning.................................................................................... vi
Package.contents................................................................................viii
Chapter.1:.
Product.introduction.
1.1.
1.2.
1.3.
Features................................................................................. 1-2
Assembling.the.monitor.base................................................ 1-2
Monitor.introduction.............................................................. 1-3
Front.of.the.LCD.monitor...................................................... 1-3
Rear.of.the.LCD.monitor........................................................ 1-5
Chapter.2:.
Setup.
2.1.
2.2.
2.3.
Connecting.the.cables........................................................... 2-2
Turning.the.monitor.on.......................................................... 2-3
Adjusting.the.monitor............................................................ 2-3
Chapter.3.
General.Instruction.
3.1.
3.2.
3.3
OSD.(On-Screen.Display).menu............................................. 3-2
Troubleshooting.(FAQ).......................................................... 3-4
Specification summary........................................................... 3-5
Supported.operating.modes................................................ 3-11
3.4.
iii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
As an Energy Star® Partner, our company has determined that this product
meets the Energy Star® guidelines for energy efficiency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian
ICES-003.
iv
Safety information
•
•
•
•
•
Before setting up the monitor, carefully read all the documentation that
came with the package.
To prevent fire or shock hazard, never expose the monitor to rain or
moisture.
Never try to open the monitor cabinet. The dangerous high voltages
inside the monitor may result in serious physical injury.
If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
•
•
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or
over a radiator or heat source unless proper ventilation is provided.
The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supply
to your home, consult your dealer or local power company.
•
•
•
Use the appropriate power plug which complies with your local power
standard.
Do not overload power strips and extention cords. Overloading can
result in fire or electric shock.
Avoid dust, humidity, and temperature extremes. Do not place the
monitor in any area where it may become wet. Place the monitor on a
stable surface.
•
Unplug the unit during a lightning storm or if it will not be used for a
long period of time. This will protect the monitor from damage due to
power surges.
•
•
Never push objects or spill liquid of any kind into the slots on the
monitor cabinet.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100-240V AC.
•
If you encounter technical problems with the monitor, contact a
qualified service technician or your retailer.
v
Care & Cleaning
•
Before you lift or reposition your monitor, it is better to disconnect
the cables and power cord. Follow the correct lifting techniques when
positioning the monitor. When lifting or carrying the monitor, grasp the
edges of the monitor. Do not lift the display by the stand or the cord.
•
•
Cleaning. Turn your monitor off and unplug the power cord. Clean the
monitor surface with a lint-free, non-abrasive cloth. Stubborn stains
may be removed with a cloth dampened with mild cleaner.
Avoid using a cleaner containing alcohol or acetone. Use a cleaner
intended for use with the LCD. Never spray cleaner directly on the
screen, as it may drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
•
The screen may flicker during the initial use due to the nature of the
fluorescent light. Turn off the Power Switch and turn it on again to
make sure that the flicker disappears.
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
•
When the same image is displayed for hours, an afterimage of the
previous screen may remain after switching the image. The screen will
recover slowly or you can turn off the Power Switch for hours.
•
When the screen becomes black or flashes, or cannot work anymore,
contact your dealer or service center to fix it. Do not repair the screen
by yourself!
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when
trying to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
vi
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1. ASUS websites
The ASUS websites worldwide provide updated information on ASUS
2. Optional documentation
Your product package may include optional documentation, such
as warranty card, that may have been added by your dealer. These
documents are not part of the standard package.
vii
Package contents
Check your MB19/MB17 Series LCD package for the following items:
LCD monitor
Quick Start Guide
Support CD
1 x Power cord
1 x VGA cable
1 x DVI cable (MB19TU only)
1 x Audio cable
1 x Cable holder
If any of the above items is damaged or missing, contact your retailer
immediately.
viii
Chapter 1
This chapter gives a general description of
the ASUS LCD monitor MB19/MB17 Series.
The chapter lists the monitor features
including introduction on the front and rear
panels.
1.1
Features
•
•
•
19”/17” LCD Monitor
Recommended resolution: 1280 X 1024
MB19TU: 2ms (Gray to Gray) Rapid response time
MB19SE/MB17SE: 5ms (Tr+Tf) Quick response time
•
•
•
•
•
•
•
•
•
•
SPLENDID™ Video Enhancement Technology
5 Video preset modes switiched by hotkey
3 Skin-tones selection
Microsoft Windows® 2000/XP compliance
VESA Display Data Channel DDC2B compliance
VESA wall mount compliance (100x100mm)
EPA ENERGY STAR® and ergonomic design
Both VGA and DVI-D Inputs (MB19TU only)
2W x 2 Stereo speakers and earphone output
RoHS compliance
1.2
Assembling the monitor base
1-2
Chapter 1: Product introduction
1.3
Monitor introduction
Front of the LCD monitor
Stereo
speakers
MENU
Base
MENU
1
2
3
4
5
6
1. Headphone port
mini-plug (3.5mm).
. This port connects a headphone with a stereo
2.
“S” Button:
•
Use this hotkey to switch from five video preset modes (Game
Mode, Night View Mode, Scenery Mode, Standard Mode, Theater
Mode) with SPLENDID™ Video Enhancement Technology.
Exit the OSD menu or go back to the previous menu as the OSD
menu is active.
•
•
Automatically adjust the image to its optimized position, clock,
and phase by pressing the button for 2-4 seconds.
3. “-” Button:
•
Press this button to decrease the value of the function selected
or move to the previous fuction.
•
This is also a hotkey for Volume adjustment.
ASUS LCD Monitor MB19 Series/MB17 Series
1-3
4. “+” Button:
•
Press this button to increase the value of the function selected
or move to the next function.
•
This is also a hotkey for Brightness adjustment.
5.
6.
Button:
•
Press this button to enter/select the icon (function) highlighted
while the OSD menu is activated.
Power Button
•
•
Press this button to turn the monitor on/off.
The table below shows the status of the LED indicator beside this
button.
Status
Blue
Description
ON
Amber
OFF
Standby mode
OFF
The headphone is purchased separately.
1-4
Chapter 1: Product introduction
Rear of the LCD monitor
AC IN
DIGITAL
ANALOG
AUDIO
AC IN
IGITAL
ANALOG
AUDIO
1
2
3
4
1. AC-in port. This port connects the power connector by the bundled
power cord.
2. DVI port. (MB19TU only) This 24-pin port is for PC (Personal
Computer) DVI-D digital signal connection.
3. VGA port. This 15-pin port is for PC VGA connection.
4. Audio-in port. This port connects PC audio source by the bundled
audio cable .
ASUS LCD Monitor MB19 Series/MB17 Series
1-5
1-6
Chapter 1: Product introduction
Chapter 2
This chapter provides instructions on how to
correctly connect cables and properly adjust
the angle of the LCD monitor.
2.1
Connecting the cables
1. Connect the cables as shown:
A
C
I
N
GITAL
ANALOG
AUDIO
Power cord
Audio cable
VGA cable
DVI cable
•
•
•
To connect the audio cable: connect one end of the audio cable to
the monitor’s Audio-in port, and then connect the other end to the
computer multi-media (or audio) card’s audio output.
To connect the power cord: connect one end of the power cord
securely to the monitor’s AC input port, the other end to a power
outlet.
To connect the VGA/DVI cable:
a. Plug the VGA/DVI connector to the LCD monitor’s VGA/DVI port.
b. Connect the other end of the VGA/DVI cable to your computer’s
VGA/DVI port.
c. Tighten the two screws to secure the VGA/DVI connector.
2. Gather all the cables, then hold them with the cable holder. Align the
cable holder to the two slots near the base and close it carefully. A
click indicates that the cable holder has been closed securely.
Cable
holder
2-2
Chapter 2: Setup
|